Researchers have developed a new design for the framework of columns and beams that support bridges, called "bents," to improve performance for better resistance to earthquakes, less damage and faster on-site construction. The faster construction is achieved by pre-fabricating the columns and beams off-site and shipping them to the site, where they are erected and connected quickly.
Talk about a cosmic caffeine jolt. The...
New robot guides at a Tokyo museum look so eerily...
HorseFly has eight rotors, a wirelessly recharging battery and a mission to deliver merchandise right to your doorstep. The new drone is the result of collaborative efforts by the Univ. of Cincinnati and AMP Electric Vehicles makers of the WorkHorse all-electric delivery truck. The newly designed, autonomous unmanned aerial vehicle was developed to work in tandem with AMP's delivery trucks to deliver packages in an efficient way.
The skies off the Hawaiian island of Kauai will be a stand-in for Mars as NASA prepares to launch a saucer-shaped vehicle in an experimental flight designed to land heavy loads on the red planet. For decades, robotic landers and rovers have hitched a ride to Earth's planetary neighbor using the same parachute design, but NASA needs a bigger and stronger parachute if it wants to send astronauts there.
The SuperDraco thruster, an engine that will power SpaceX’s Dragon spacecraft to orbit, has completed a test regimen held over the last month at SpaceX’s Rocket Development Facility in Texas. This qualification test involves a variety of conditions conditions including multiple starts, extended firing durations and extreme off-nominal propellant flow and temperatures.
According to new research from Sweden, two aircraft engine concepts, a geared turbofan and an open rotor, can enable a significant reduction to aircraft fuel consumption. With an open rotor, the potential reduction is 15%. An open rotor engine generates most of the thrust from two counter-rotating propellers instead of a ducted fan. This enables a larger engine diameter and a higher propulsive efficiency.
In a typical wind farm, the wind turbine located in the wakes of upstream turbines would experience a much different surface wind compared to the ones located upwind due to wake interferences. Scientists at Iowa State Univ. have completed a study on the effects of these relative rotation directions, using two tandem wind turbines as a model. They found a big difference in performance between co-rotating and counter-rotating turbines.
Although lubricants for machinery are widely used, almost no fundamental innovations for this type of product has been made in the last 20 years, according researchers in Germany who have been working on a new class of lubricating substance. Their new liquid crystalline lubricant enable nearly frictionless sliding because although it is a liquid, the molecules display directional properties like crystals do.
Pipes, rails, and wires are typically manufactured at high speeds, which makes in-line inspection efforts difficult. This is because micro-defects take time to detect, even with machine vision technology. A new optical inspection system developed in Germany reviews the workpieces at 10 m per second, as fast as an Olympic sprinter, and finds defects in real time that can be as narrow as a single hair.
Industrial plants must function effectively. Remedying production downtimes and breakdowns is an expensive and time consuming business. That is why companies collect data to evaluate how their facilities are doing. At the Hannover Messe Digital Factory, held April 7-11, researchers in Germany will show how operators can analyze these huge amounts of data and use it as an early warning system when problems threaten.
Small wind turbines tend to be located in areas where wind conditions are more unfavorable and control systems of current wind turbines cannot adapt. To address this problem, researchers in Spain have developed an adaptive algorithm that can contribute toward making these miniature turbines more efficient.
For the past 100 years, the way your fridge preserved your food has been rooted in technology dating back to the mid-1800s, but that is about to change. GE researchers are developing a new magnetic refrigeration method that uses no refrigerants or compressors and is 20% more efficient than what is used today.
Additive manufacturing, or 3-D printing, offers a compelling alternative to more traditional manufacturing approaches at NASA, where the need for highly customized spacecraft and instrument components is quite high. The agency has recently launched a number of formal programs to prototype new 3-D printed components, including rocket engine injectors, and 3-D printers for use in space.
Stratasys, a manufacturer of 3-D printers and materials for personal use, prototyping and production, has announced the launch of the ground-breaking Objet500 Connex3 Color Multi-material 3-D Printer, the first and only 3-D printer to combine colors with a variety of photopolymer 3-D printed materials.
According to Anupam Agrawal, a professor of business administration at the Univ. of Illinois, Urbana-Champaign, firms can manage their sourcing better by developing relationships not only with their suppliers but also with their suppliers’ suppliers. The lack of communication or collaboration between the big players at either end of the supply chain spectrum can prevent gains in efficiencies.
Ultra-short laser pulses provide a fast and precise way of processing a wide range of materials without excessive heat input. Scientists from Bosch, TRUMPF, Jena Univ. and Fraunhofer Institute in Germany have turned the ultra-short pulse laser into an effective series-production tool. This type of laser can remove, or ablate, tiny areas measuring just a few nanometers.
A new device transforms almost any bicycle into an electric-hybrid vehicle using an app on a smartphone. The device, called the Copenhagen Wheel, is is equipped with wireless connectivity to track travel and installed as part of a rear hub of a bike wheel. Packed with a proprietary computer, batteries, and sensors that monitor how hard a rider is pedaling, it activates an onboard motor whenever support is needed.
Google may be gearing up to build robots that resemble props in science-fiction movies as the ambitious Internet company expands into yet another technological frontier. To gather the expertise and research it needs, Google has purchased eight companies that specialize in robotics this year. The acquisitions are being assembled into a new robotics division headed by Andy Rubin, who oversaw Google's development of Android.
The Titan Arm, a robotic device invented by Univ. of Pennsylvania engineering students, looks and sounds like part of a superhero's costume. But its creators say it's designed for ordinary people—those who need either physical rehabilitation or a little extra muscle for their job. The arm can help its wearer carry an additional 40 pounds.
Professor Ken Naitoh of Waseda Univ.'s Faculty of Science and Engineering has discovered a new compressive combustion principle that could yield engines with a much higher level of thermal efficiency: up to 60% or more in applications including automobiles, power generation and aircraft.
Two of the key instruments aboard NASA’s Curiosity rover on Mars are the CheMin, a mineral sample analyzer, and the ChemCam, a spectroscopic imaging system. Both systems require precise, fast motion control, capable of surviving a harsh environment. Jet Propulsion Laboratory engineers found a solution with piezo-based technology from Physik Instrumente and miCos. But first it would need to pass rigorous testing.
Hydromat collets from Hardinge are manufactured to rigid specifications including material, heat treatment and accuracy for the high-production environment. Every Hydromat collet’s thread, back bearing, taper gage line and spread are manufactured with dedicated gages.
Clippard Instrument Laboratory’s new PQ-FV In-Line Flow Controls can be easily added to existing circuitry and are lightweight and compact in size. The PQ-C Elbow Controls are ideal for low cost and lightweight applications when mounting directly to an NPT port on a cylinder or valve is required.
A new maritime propulsion technology called the RudderPod, which steers independently of the main propulsion unit, could save up to half a million euros in fuel costs, according to the TRIPOD research project collaborators in Europe who plan to retrofit the new system to a ship for testing. The project aims to improve propeller efficiency as well by integrating RudderPod with new types of propellers.
The National Science Foundation, in partnership with the National Institutes of Health, U.S. Department of Agriculture and NASA, has announced new investments totaling approximately $38 million for the development and use of robots that cooperatively work with people to enhance individual human capabilities, performance and safety.
In recent years, the development of devices known as plasma actuators has advanced the promise of controlling flows in new ways that increase lift, reduce drag and improve aerodynamic efficiencies. A Univ. of Florida team has been engineering their own variety, called serpentine plasma actuators, which imparts a greater level of versatility in flow control.
Chinese scientists described the country's first moon rover on Wednesday and invited the global public to come up with a name for it. The rover has two wings, stands on six wheels, weighs 140 kg and will be powered by solar energy. It will soft-land on the moon after a launch aboard the spacecraft Chang'e-3 in December.
- Page 1