Gov't says it cannot explain runaway Prius

Posted In: Manufacturing

By ELLIOT SPAGAT - Associated Press Writers - Associated Press

Monday, March 15, 2010

newsvine diigo google
slashdot
Share
Loading...

The federal government said Monday it cannot explain a reported incident of sudden, high-speed acceleration in a Toyota Prius on a San Diego, Calif., freeway last week.

The National Highway Traffic Safety Administration said in a statement that it continues to investigate but "we may never know exactly what happened with this car."

The agency said its engineers are reviewing data from the Prius owned by James Sikes to try to understand what happened with his hybrid. But so far, NHTSA says it has not been able to find anything to explain the incident that Sikes reported.

Sikes called 911 last Monday to report losing control of his Prius as the hybrid reached speeds of 94 mph. A highway patrol officer helped bring the vehicle to a safe stop.

Inspectors in California tried during a two-hour test drive to duplicate the acceleration, but were unable to do so.

John Gomez, an attorney for Sikes said the failure to repeat the incident is insignificant and not surprising.

"They have never been able to replicate an incident of sudden acceleration. Mr. Sikes never had a problem in the three years he owned this vehicle," he said Sunday.

But Kurt Bardella, a spokesman for Rep. Darrell Issa, R-Calif., said the failure to duplicate the stuck accelerator, along with a vehicle design to prevent such occurrences, raises questions about the driver's story.

"We're not saying Mr. Sikes is wrong or that he lied, we're saying that questions have arisen in the investigation," Bardella said.

Toyota Motor Corp. planned to announce preliminary findings of its investigation at a news conference Monday in San Diego.

NHTSA is looking into claims from more than 60 Toyota owners that their vehicles continue to accelerate unexpectedly despite having their vehicles repaired.

Technicians with the NHTSA and Toyota could not duplicate what Sikes said he experienced March 8 on a mountainous but lightly traveled stretch of Interstate 8 east of San Diego, according to a congressional staffer's memo prepared for the House Committee on Oversight and Government Reform.

"Every time the technician placed the gas pedal to the floor and the brake pedal to the floor the engine shut off and the car immediately started to slow down," the memo read.

According to the memo, a Toyota official who was at the two-day inspection last week in suburban San Diego explained that an electric motor would "completely seize" if a system to shut off the gas when the brake is pressed fails, and there was no evidence to support that happened.

"In this case, knowing that we are able to push the car around the shop, it does not appear to be feasibly possible, both electronically and mechanically that his gas pedal was stuck to the floor and he was slamming on the brake at the same time," according to the memo.

Toyota has recalled millions of cars because of floor mats that can snag gas pedals or accelerators that can sometimes stick. Sikes' car was covered by the floor mat recall but not the one for sticky accelerators. He later told reporters that he tried to pull on the gas pedal during his harrowing ride, but it didn't "move at all."

The Prius is powered by two electric motor-generators and a small gasoline engine, all connected by transmission gears. A computer, which Toyota calls the "hybrid control computer" determines what combination of motors is needed and which would be most efficient.

Craig Hoff, a professor of mechanical engineering at Kettering University in Flint, Mich., said that for the Prius to accelerate out of control, at least two systems would have to fail simultaneously. They are the sensor signal that tracks the brake and gas pedal positions when the driver presses on them and the hybrid control computers.

"The chance of them both going wrong, plus the fact that the signal is bad, it just seems very, very, very remote," Hoff said. "Could it happen? Statistically, yes. But it just doesn't seem very likely."

Several events usually combine to cause problems with cars, and it's difficult to reproduce them, Hoff said.

"It's going to make it really hard to find, because you've got to line up the multiple effects," he said.

The congressional memo said both the front and rear brakes were worn and damaged by heat, consistent with Sikes saying that he stood on the brake pedal with both feet and was unable to stop the car. But if the fail-safe system worked properly, the brakes wouldn't have been damaged because power would have been cut to the wheels.

Gomez said the best evidence that his client was frantically slamming the brakes is that a California Highway Patrol officer who was giving Sikes instructions over a loudspeaker smelled burning brakes and saw the lights on.

___

Spagat reported from San Diego. AP Auto Writer Tom Krisher contributed to this report from Detroit.

JOIN THE DISCUSSION
Rate Article:  Average 0 out of 5
Register or log in to comment on this article!

0 Comments

Add Comment

Text Only 2000 character limit

Page 1 of 1

New To Market

more

Spindle company to adopt wireless maintenance system
Spindle company to adopt wireless maintenance system

GTI Spindle Technology is partnering with InCheck Technologies to demonstrate InSite – a new online wireless predictive maintenance system – at a conference at the International Manufacturing Technology Show in Chicago, Ill., Sept. 13-18. InSite provides data collection, storage, and processing facilities for condition and performance monitoring.

Small USB box provides plug-in modules, 200 kS-s and isolation

The DEWE-50-USB2-8 from Dewetron incorporates real plug-in signal conditioning modules for low and high voltages, strain, pressure, acceleration, sound, temperature, force, and more. It can be used in demanding high voltage environments safely.

Tools & Technology

more

Fused silica capillary tubing
Fused silica capillary tubing

Delivering reliable operation in demanding conditions, Fiberguide Industries introduced its new line of fused silica capillary tubing.

High-temperature protective coatings

Aremco Products, Inc. offers the Corr-Paint line of protective coatings—suited for protecting metals, graphites, and refractories used in ovens, boilers, furnaces, heaters stacks, and heat exchangers to 2500°F.

Advertisement

Advertisement